噴漆面鋁合金自干油墨

更新日期：2023年02月09日
有效期：360天
瀏覽次數：

價格：￥180
供貨總量：10000
規格：1公斤
所屬行業：表面處理-> 絲印-> 絲印
關鍵字：噴漆面鋁合金油墨鋁合金噴漆面油墨自干鋁合金油墨

【想采購，免費發布采購需求】

趙綠林

點擊詢盤

手機查看

商家資料

凱賢實業（上海）有限公司

聯系人：趙綠林
部門：銷售部
職位：銷售經理
電話：

手機：

地址：中國上海上海外岡鎮西岡身路777號

進入商鋪

在線留言

主營：

PP料免處理油墨 PE料免處理油墨自干五金油墨

企業其他產品更多>>

￥180
耐酸堿鋁合金自干油墨

上海上海
￥180
耐酸堿鋁合金絲印油墨

上海上海
￥180
絲印耐酸堿鋁合金油墨

上海上海

產品詳情
聯系方式

噴漆面鋁合金自干油墨銷售廠家！

本產品主要用于各種金屬、玻璃、真空電鍍、水電鍍、電泳、陽極氧化鋁、電解板、鋁塑板、噴塑、噴粉、靜電噴漆面、烤漆面以及各種天花吊頂氧化板、鏡面板、覆膜板、輥涂板等制品的絲印及移印。
油墨特性：
1、平光、附著力佳、耐汽油、耐化學品；
2、手感好，流平性佳、面光潔；
3、表面硬度好，耐沖擊性能強、抗刮傷；
4、耐汽油、耐酒精、耐化學品程度佳；
印刷：
選用網目為100-350目，以120T網紗計算涂覆蓋面積每公斤達30~35㎡。
表干時間自然揮發5-15分鐘，實干時間在24小時以內，48小時后達性能。
1．用配套專用稀釋劑開油水
2．用718洗網水洗網。
3．或添加配套硬化劑10%可增加附著力,提高墨膜硬度。
4．烤箱80℃烘烤10分鐘佳能更優。
測試方法（完全干燥后）：
1．3M膠紙粘在畫有百格的油墨表面45度角迅速拉起不脫油。

使用方法：
1．建議用我公司專用稀釋劑進行稀釋，不建議使用783慢干稀釋劑稀釋，使用前應充分攪拌，用后隨時密封。
2．攪拌時加本公司配套開油水10-12%，稀釋到印刷適合粘度，移印稀釋使用移印專用稀釋劑；用718洗網水清洗。
3．不得與其它類型油墨混合使用，否則容易出現其他附著力，化學反應等不良現象。
4. 加入固化劑的油墨使用時限為8小時，過期請棄用，剩余油墨不可回收
注意事項：
1．各種承印物料的外觀相似，但可能會是不同的材料，客戶需先試印，確其符合要求后，再批量生產。
2．在移印過程中，如出現拉絲或散開，可適當加入一些慢干膏即可;
3．環境溫度過高，將會影響油墨原有質量。白色超越150都會變色，烘烤時請用木質材料墊底進行烘烤，不得直接接觸鐵
4．根據氣候變化，請遠離火源，陰暗處15度-30度環境下存放
Brand: but MY name: anodic oxidation INK Numbers: 65496
Anodic oxidation ink series
The product is produced with advanced import acrylic resin and senior pigment after fine grinding system,ed inbination to ABS, PP, PET, all kinds of metal, glass, ceramic, stone, electroplating (water cut electroplating), anodic alumina surface and roast (spray paint products of screen and pad printing, not needing curing agent, and does not need to bake, can obtain excellent adhesion.
Ink characteristics:
1 the classification includs glass, adhesion, good resistance to gasoline, alcohol, resistance to chemicals;
2, feel is good, flow ping sex, good surface is bright and clean;
3 and fine surface hardness, impact resistance properties of strong, resistance to scratch;
4, resistant to gasoline, alcohol, resistant to chemicals resistant degree good;
Printing:
Choose for 100-350 mesh mesh to 120 Ts yarn with coverage area calculation per kilogram of 30 to 35 ㎡.
Dry time table natural volatilize 5 to 15 minutes, action in time within 24 hours, after 48 hours of optimum performance.
1. With matching special thinner, open oil and water
2. Wash washings with 718.
3. Or add hardener 10% supporting can increase adhesion, improve ink film hardness.
4. Preheat the oven to 80 ℃ bake for 10 minutes Canon even better.
Test method (dry) :
1.3 M tape stuck in the picture has's ink surface 45 degree Angle quickly pull up not to take off oil.
2. The purity of 99% alcohol 500 G force in ink surface wipe 300 times back and forth without decoloring.
Method ofe:
1. The proposal with mypany special thinner to dilute, not rmended dry thinners diluted 783 slow, before thee should be fully mixing,e at any time after sealing.
2. Add thepany supporting stirring open 10 to 12%, oil and water dilute the printing for viscosity, pad printing dilutione moving printing special thinner,;e clean water to wash thes 718.
3. Not with other kinds of printing ink mixede, otherwise easy to have other adhesion, chemical reactions and other bad phenomenon.
4. Add hardener inkse time limit for 8 hours, please noted, the remaining expired ink not recycling
Note:
1. All kinds of printing material appearance similar, but may be of different material, tomers are required to meet the requirements of the ShiYin, indeed, its, then batch production.
2. In moving printing process, such as a wire drawing or away, can be appropriately to add some slow dry paste can;
3. Environmental temperature is too high, will influence the quality of the original ink. White will change color, roasted beyond 150 when pleasee woodiness material bottom, and may not directly contact roast iron
4. ording to climate change, please away from fire, the shadows 15 degrees-30 degrees environment for